Stainless Steel Pipe, Tube, Fittings, Flanges, Valves

This instruction describes the pre-assembly of a cutting ring (SRD…VA) on the stainless steel pipe in the assembly stud and the finishing assembly of the cutting ring in the screw sleeve. Manufacturers such as Victaulic and Grinnell produce sleeve-clamp fittings which are replacing many flange connections. They attach to the end of a pipe segment via circumferential grooves pressed around the end of the pipe to be joined. They are widely used on larger steel pipes, and can also be used with other materials.

The lighter rubber fittings may not muffle sound as well as the heavy cast-iron fittings. In addition, some conservative plumbing codes still require leaded hub joints for final connections where the sewer main leaves a building. Although low-priced wyes are often spot-welded, industrial-strength wyes are flash-welded at each seam. In long-distance pipeline applications, a specialized wye is used for allow insertion of pigging to keep pipes clear and maintain flow.

In a long radius elbow, the centreline radius is 1.5 times the nominal size of the pipe or you can say 1.5 times the diameter of the pipe. Normally long radius elbows are used in piping as pressure loss is less as compared to short radius elbow. Elbows are available in two radius types, Short radius and Long Radius (1.5D).

malleable cast iron pipe fittings

Pipe welding is often performed by specially licensed workers whose skills are retested periodically. For critical applications, every joint is tested with nondestructive methods. Because of the skills required, welded pipe joints are usually restricted to high-performance applications such as shipbuilding, and in chemical and nuclear reactors. Although they are usually used to attach pipe and fittings to mechanical supports in buildings, they do not connect the pipes to each other.

Such as both plain ends or one plain and one threaded end. With over 10,000 unique products, we provide a wide range of strong, lightweight and versatile reticulation solutions. Reducer is a pipe fitting component which reduces the flow size from larger to smaller by reducing size of pipe. One is concentric reducer which is like cone shaped with gradual decreasing around the pipe but in this case accumulation of air may possible and it results in cavitation.

Fasteners commonly used with piping are a stud bolt with nuts ; a machine bolt and nut; or a powder-actuated tool fastener . This fitting (also known as a “bungalow fitting” or a “cottage fitting”) is a sanitary tee that allows two trap arms to be connected at the same level. Clean-outs are fittings with removable elements, allowing access to drains without the removal of plumbing fixtures.

Fittings require money, time, materials, and tools to install, and are an important part of piping and plumbing systems. Valves are technically fittings, but are usually discussed separately. Choosing the material of your pipe fitting comes down to what will be running through the pipe. From fittings perfect for cold water supplies to reliable options for gases and chemicals wastes, we carry a variety of fitting options to help you get the job done.

Union is a type of fitting, which functions as similar to coupling. But coupling cannot be removed after fixing but in this case we can remove the union whenever we needed. Although compression connections are less durable than soldered connections, they are easy to install with simple tools. However, they take longer to install than soldered joints and sometimes require re-tightening to stop slow leaks which may develop over time. Because of this possible leakage, they are generally restricted to accessible locations , and are prohibited in concealed locations such as the interiors of walls.

Large diameter welded fittings are manufactured from the plate. BFO understands the importance of a honest and reliable vendor. From order fulfillment accuracy to experienced technical support representatives, we believe that you should be able to find all of your products and answers you have, in one place.

A reducer can also be used either as a nozzle or diffuser, depending on the mach number of the flow. Dielectric unions, with dielectric insulation, separate dissimilar metals to prevent galvanic corrosion. When two dissimilar metals are in contact with an electrically conductive solution , they form an electrochemical couple which generates a voltage by electrolysis. When the metals are in direct contact with each other, the electric current from one to the other also moves metallic ions from one to the other; this dissolves one metal, depositing it on the other. A dielectric union breaks the electrical path with a plastic liner between its halves, limiting galvanic corrosion.

You may also like

Leave a Reply

Your email address will not be published. Required fields are marked *